Re: bolt_nut_mcat.ptd and BOLT_TYPE
It is the type of bolt, threaded, stud, etc thanks Jim
View ArticleRe: Shift surface problem
Hello, Sorry to answer so late. If I well understand, I have to use the new cone and the new surface you created (upperskinV5) to draw my lower skin (offset 10.2mm). I'm sorry, but it's hard for me to...
View ArticleStarted Off Fine And Then Things Are Working In Slow Motion Now!
Hello Community, I'm trying to learn a CAD program so I can design an electric tractor. I recently downloaded Creo Element/Direct Modeling Express 4.0 and started with the tutorials to get familiar...
View ArticleRe: Convert mathcad 3.0 to 2.0?
Mea culpa David, after reading Nicklas' original request I was hoping someone may have found a workaround or a way to covert on his behalf, fully realizing what he was looking was a measure of forward...
View ArticleRe: How to get CoCreate 17.00 running after upgrading to Win 8.1
You cannot "move" a license over to another system just by copying the MEls.conf file.The licenses in MEls.conf are generated for a "HW-ID" which is either a MAC-Adress of NICor it is the ID of...
View ArticleRe: Shift surface problem
Marc, I did try to work with these surfaces some more. Not having much luck with IDD, the surfaces are very problematic. Your assumptions are correct. I am suggesting making a good inner skin...
View ArticleClik here to view.
Re: WHIRL MIXER
Technically, this is what the drawing defines without further information. No method of attachment of the vanes. Also, dimensions b & c are assumed as 30 and 50, although it leaves a non-circular...
View ArticleRe: Started Off Fine And Then Things Are Working In Slow Motion Now!
Most often when software suddenly goes from speedy to slow the reason is the memory requirements have moved from all in-memory to being large enough to page to disk. You may just have outgrown the...
View ArticleRe: Started Off Fine And Then Things Are Working In Slow Motion Now!
Hi David, Thanks for takng the time to reply to my question. I'm still in the tutorials and I can't manipulate the simple little lego block that they ask you to draw! I would imagine that that is a...
View ArticleRe: Mass properties of a sectioned assembly
HI, Cross section is a visualisation tool only, mass properties will not reflect it. If you want true MP update you need to perform assembly level cut on the top assembly. You can use same datum plane...
View ArticleClik here to view.
Is it possible to use the explicit keyword on functions?
Hello,I’ve got Mathcad v15.With the explicit keywords it’s easy to see your equation with the inserted variables. But what about functions? I can’t do that.For example: I want to calculate new yield...
View ArticleClik here to view.
Modeling a wing help?
Hello, so I am trying to model a wing here but i am stuck with a problem.I want the wing to curve at the end (like the picture at the bottom) but I just seems like I can't find any way to do it.I've...
View ArticleClik here to view.
Re: Is it possible to use the explicit keyword on functions?
The explicit modifier is far away from being perfect, but what you demand can be done. Nevertheless there is a drawback as "float" is used which affects overall calculation precision. See my remarks in...
View ArticleRe: Creo Simulate Result Window template with legend values: bug?!
Hi Laurens, Can you upload the file? I would like to take a look at it.
View ArticleRe: Is it possible to use the explicit keyword on functions?
Thank you for your explanation about float. I will use it with caution.
View ArticlePlotting a simple straight line in 3D
Hello... I can't believe I have to ask...meaning that I can't figure this out, but here goes. I have been trying to create a mock-up plot in 3D (x, y & z), and each thing I try I end up having to...
View ArticleRe: Plotting a simple straight line in 3D
[Sigh].....I figured it out. I don't know how to delete this post however, so it's not sitting in the list cluttering things up.
View ArticleClik here to view.
Your thoughts on tools for rapid identification and visualization of CAD...
The SketchRec 1.1 Beta SW by Imagars is capable of rapidly identifying complex design files of interest (2D or 3D), including Pro/Engineer part files. The tool automatically displays thumbnail images,...
View Article