Re: Unable to Check-In Part?
Sounds like you have something set in SAP that is not letting you change a part once it has been uploaded and published. Try deleteing the published file and check you part attributes for a flag. Also...
View ArticleRe: Swept Blend with multiple trajectories?
The limitation of the VSS is that you cannot have an arc segment turn into a line segment, or, worse, try and invert. When the radius goes to infinity, it divides by zero.... (a pun, meaning it...
View ArticleClik here to view.
what is it that i am missing?
I have followed jlinkug.pdf, setting up j-link, and the sample applications, installing j-link, sample applications, and install test. I have tried over and over again but still no luck. here is my...
View ArticleRe: Swept Blend with multiple trajectories?
I'll wave the flag for the curvature-controlled element. There should be no problem because curvature only goes to infinity at a sharp corner, which is actually not realizable as even the sharpest...
View ArticleHow to Couple Belt Cleats to Pulleys
Hi all.I am working with Creo 3.0 and need to perform a motion analysis of a handoff between cleats on two conveyors. The conveyors will physically be chains but for my analysis, either a chain or...
View ArticleClik here to view.
Re: Has anyone done an ACM (Arbortext Content Manager) to PDMLink migration?
The Windchill Bulk Migrator can be used to migrate data from one Windchill solution to another. Take a look at the below article which gives information about the capabilities of the...
View ArticleRe: Options tab in surface copy command does not work
I tried the mapkey and it did not work. So I removed M030 and installed M010 and it work! so I reinstalled M030 and now it works. I talked with Customer service and they think it was a graphic card...
View ArticleRe: Options tab in surface copy command does not work
Adam, You may mark your reply as correct answer for the post.
View ArticleRe: Mouse wheel zoom not working on Windows 8.1
Just upgraded to IsoDraw 7.3 from 7.2. Lost the ability to reduce/enlarge graphic size via mouse wheel. I do not have WizMouse on my system. Any fixes available?
View ArticleRe: Mouse wheel zoom not working on Windows 8.1
What Darko said. Set that config option has worked for others.
View ArticleClik here to view.
Defining variable greater than/equal or less than/equal
I was trying to draw this graph, but how im supposed to define x ?
View ArticleRe: License request failed for feature
License request failed for featureRequesting PROE_FoundationAdv ...7788@reza-w8: (-97) The desired vendor daemon is down.
View ArticleRe: How to disable the option Monochrome display from active view in Creo view
Athmanand, Yes it is possible. This needs to be added to the admin_prefs.xml file and pushed out to the users.
View ArticleRe: License request failed for feature
License request failed for featureRequesting PROE_FoundationAdv ...7788@reza-w8: (-97) The desired vendor daemon is down.
View ArticleClik here to view.
How do you flip the axis direction of an explode line?
I am adding explode lines to an explode view in Creo but I can't change the direction of the lines when they are pointing in the wrong direction. The flip button is greyed out.
View ArticleRe: USER DEFINED TOOL PARAMETERS
Yes, since the threads are now in the knowledge database, it makes sense to add information to them, even if the topic is far from being hot.And yes, they should be fully indexed, like articles and...
View ArticleClik here to view.
Re: How do you use undefined variables?
Kasper Rieder wrote: Thanks for the quick response! However, is this really the only way to do this? The reason I'm asking is that I have a system of 8 unknown variables, where there is 5 known values,...
View ArticleRe: How do you use undefined variables?
As Stuart notes, it depends on whether you are doing symbolic or numeric math. If you are doing numeric math, then Mathcad cannot handle an undefined variable, unless it's a parameter in a function...
View ArticleRe: Delete the PTC-Account
As I've mentioned in a previous discussion:If any PTC Community member wishes to disable their account all they need to do is email us at: community@ptc.com Please keep in mind that you will need to...
View Article