Help for updating the Windchill ASM.
We have copied the old ASM and created new one but before releasing it, The structure of old ASM got updated and released by some other user so we need those structure changes should reflect in our new...
View ArticleRe: [Integrity] How do I checkout a sub-project in a top level project?
Hi Snaku, assuming that #/168/ is your registererd top level project, the following config-path should do the job: #/168/#DAP2500AB A Read the CLI Reference for Configuration Management (section...
View ArticleClik here to view.
Simulation non linéaire avec matériau élasto-plastique
Bonjour à tous ! Je suis nouveau sur le forum, mais pas nouveau à utiliser les produits PTC car je l'utilise depuis 2007 (licence professionnelle), et plus particulièrement depuis 2008 dans mon...
View ArticleClik here to view.
Re: Create a function as ODEs solution
Valery Ochkov wrote: We can create a function as a PDEs solution:Nice Valery, but probably not good practice to plot for a time beyond the end of the time (T) for which the PDE has been solved! Alan
View ArticleRe: How do I define custom derivation rules for calculating error marigin in...
AlanStevens wrote: Werner Exinger wrote: I see no practical way to automate this, though. No, but with a complicated function it might be less error prone to use Mathcad in this way. Yes, and here...
View ArticleRe: CSPLINE and iteration
thanks Werner. Make sense now!How does one interpolate between 2 sets of known data then? For example (see also attached) if one has data for a ratio b/d=0.1 and b/d=0.2 but one wants a Y value (K on...
View ArticleClik here to view.
Re: how to use "flat pattern" and get rid of useless lines
Hello Brandon try to look at this before i start work if you view your pattern from the other side the lines do not appearMaybe you knew this already I remodeled the flange with my start post result in...
View ArticleClik here to view.
Re: how to use "flat pattern" and get rid of useless lines
Ok i managed to get it done before i start result the lines do not appear when i remodel G
View ArticleRe: CSPLINE and iteration
J B wrote: thanks Werner. Make sense now!How does one interpolate between 2 sets of known data then? For example (see also attached) if one has data for a ratio b/d=0.1 and b/d=0.2 but one wants a Y...
View ArticleChange all name of Drawing in Creo & Creo element direct
Dear ALL I have one example to change all name of Drawing in Creo & Creo element Direct:Part A - name in sheet drawing is 1234 - CPart B - name is 1234 - BPart C...
View ArticleSimplified Represntation
I have created parts with multiple features.Placed in simplified repesentaion.But in drawing views-Properties-view states-simplified representation is deactived.How to activate it ?
View ArticleRe: Dynamic table of content
I realise this is an old post, but I am relatively new to Mathcad and need to set up a dynamic table of content. I cannot seem to link to the original document to uploaded. Do you perhaps still have it...
View ArticleRe: Simplified Represntation
Hello, you have to set the required Simplified Rep. Do this by selecting Drawing Models from the Layout tab, then select Set/Add Rep, select your Rep, job done. John
View ArticleRe: Simplified Represntation
But I placed views first done dimesioning.Now to follow this process I need to delete views and then set the Simplified rep.Is it possible to set it from views properties.
View ArticleRe: [SI] freezing shared members vs. shared build projects?
Hi Jens, I know you scenario well, so I here the differences If found so far : shared subproject- definitely read only, no matter what permission the user has- there will be no "incomming change"...
View ArticleRe: how to use "flat pattern" and get rid of useless lines
Hello when i remodeld i used flat pattern and and flat pattern instance i only use the unbend when i am cutting slots or mitres or holes close to the bend lines RegardsG
View ArticleRe: Simplified Represntation
Ah!! then i think you may have a problem. You can set the Rep & add new views, but i don't think you can you force a Rep on an existing view. I thought a work around might be to create a new view,...
View ArticleDynamic Table of Content Ideas
I have started this thread as a collab has asked a question regarding dynamic table of contents in an old thread. Attached is a worksheet I have saved - Alternative Ideas welcome.
View ArticleRe: Dynamic table of content
I have just created a new thread which will hopefully attract a bit of interest and provide a few alternatives. http://communities.ptc.com/thread/52955
View Article