Re: Fasteners
Hi Mark, Yes that's sensible. I was trying to understand whether there would be any circumstances where having neither fix separation=on or contact region is desirable. If there was no contact region...
View ArticleSolver equivalent
Hy!What is the "Solver" command from Excel equivalent in Mathcad? Given Find...does not find a solution. It's only one unknown value and two equations Thanks.
View ArticleRe: Opening .igs or .stp files in CREO with the geometry in the tree.
Here is a example of using layers: Attention:You will need to update your browsers Flash Player plugin to see videos on this site. Update your Flash Player here. Its free and fast.');}); });
View ArticleRe: Solver equivalent
Is this question again soooo urgent like the ones here?http://communities.ptc.com/message/237044#237044http://communities.ptc.com/message/237045#237045 They are still marked "unanswered", so either you...
View ArticleRe: Solver equivalent
Mathcad has several solvers. The main ones are Find, Minimize, Maximize, and minerr. Which to choose depends on what you are trying to achieve.
View ArticleRe: i could not open my .xmcd files
This is a Mathcad forum. Math typos should be pounced upon. English ones, not.
View ArticleRe: How to Calculate Young's Modulus and Poisson Ratio if not given in...
One method I have used over the years. Young's Modulus = Stress / Strain ( Standard Text Book Answer)Example: I have a material data sheet, attached. see "ABS_Data_Sheet.pdf"Tensile Stress =...
View ArticleRe: problem with BOM
thanks a lot!! sorry for late reply, there were sth wrong with my internet, but you did help me solved this problem, thanks again!
View ArticleRe: Sketcher dimensions
Something in the solver is hanging that dimension. It happens a lot more in Creo than it ever happened before but it is fixable. I have not run across one that wasn't fixable in Creo 2.0. Really, it...
View ArticleRe: Angular Dimensioning
Highlight the dimension, then hold shift while dragging the text horizontal.
View ArticleRe: Exporting OpenVSP files to Creo Elements Pro
Hmmm that's interesting! Can you attach one of the files in this discussion? You can do that by using the "advanced editor" in the upper right of the comment section.
View ArticleRe: Something seems strange
I think I have worked it out i.e. the outflow orifice was too small. That said given enough time, in my view, the tank should still drain. However even if you increase the time period over which the...
View ArticleClik here to view.
Creating Degrees of Freedom in Weighted Link
In this simulation I have a large box that is simplified to a point at its center of gravity (blue point in image above). The box is tied down to the floor using the 4 vertical locating pins and 4...
View ArticleRe: Create Wizard not closing when complete in Windchill 10.1
I turned on the logging for both the CreateObjectFormProcessor and the CreateEditFormProcessorHelper and I did find an error: 2014-03-20 16:02:44,929 ERROR [ajp-bio-8010-exec-1] wt.log4javascript.PTC...
View ArticleRe: There is a wt.util.WTRuntimeException I couldn't solve it
Dear Sureshbabu AD： I have tried your suggestion, but it does not work...I also clear all queue entries inside WfPropagationQueue which status is Failed or Servere, the problem still exist. Dear Jess...
View ArticleRe: Something seems strange
Its no surprise to me that the tank isn't empty at t=120 min but only a bit later. In case of the values in your sheet the tank is empty after 157,083 minutes, then the water height in the tank gets...
View ArticleRe: Something seems strange
Werner; What can I say. If only my brain could work like yours your mathematical intuition astounds me. If you don't mind me asking what is your academic background? Kind regards, Mark
View ArticleRe: Failed to launch server application
I found the answer.. Microsoft Office 2010 64-bit Edition is not supported.I removed and installed Microsoft Office 2010 32-bit Edition and the problem solved. Thanks.
View ArticleAnyone know of a way to fix a spline length?
I'm wondering if anyone has done any work with Splines and holding the length to a fixed value? This assumes that the endpoints could not get any further apart than a straight line, but as the ends...
View Article
