Re: Pattern then merge surfaces
ah ha! see I knew I was missing someting simple. No not going to solidfy, just took some proper trimming and grouping/patterning merging order. thanks
View ArticleRe: New to Creo - Parameter Roll-Up in Assemblies
Is there a way to just view the weight value without putting it on a drawing? Or do you need to place is somewhere on the assembly drawing to see it?
View ArticleRe: Impact Analysis / Drop Test Simulation
If acceleration spectrum is known, I would propose a dynamic shock analysis. You would have to create a valid modal analysis model, use it to calculate (a large number of ) normal modes and subject to...
View ArticleRe: Maintenance: Restarting Servers
LDAP should be up when Windchill is started as well. Essentially the back-end datastores should be up first.
View ArticleTruncate dimension in a drawing
In a similar thread, there was a way to truncate the output of a parameter used as a dimension in a drawing (See thread: http://communities.ptc.com/message/191893#191893 ). What I am looking for is to...
View ArticleRe: New to Creo - Parameter Roll-Up in Assemblies
I have added the parameters to the Model Tree as additional columns. That way you can see all the values from the parts that make up the assembly as well.
View ArticleRe: Function mhyper acts quirky in M14 and M15
Mathcad's ode solver seems to be accurate to about 4 or 5 significant figures here.Which you can significantly improve by setting TOL to a lower value than the default 10^-3.
View ArticleRe: Creo vs. Solidworks vs. Inventor
I worked 10 years with Autodesk Inventor, and then, switch job to a company that uses CREO 2.0 and Solid Works. In this past 6 months, I used both CREO 2.0 and SW, changing from one to another because...
View ArticleHotspots in Isodraw - where to start
We are looking into adding hot spots to our images used in our online parts catalog system. Currently we supply a third party with pdfs and they add hotspot info to the images they create from the...
View ArticleRe: Tips for text
Naveen,Welcome to the forum. PTC is in the process of creating an editor where "What you see is what you get" per this product suggestion. I am not sure if this is available yet, or if it is going to...
View ArticleClik here to view.
Re: manual selection of method for odesolve, minerr, find in Prime
Now I know why I cannot solve this problem in Prime - I cannot choose the Fixed method in Prime but in Mathcad 15 I can:
View ArticleRe: Iterative equation
Type it in using a boolean equal sign and use a solve block with Find() to get your solution. Always better to post a worksheet rather than a pic!
View ArticleRe: XY Plot
You had two errors:1) The RHS of three definitions t2f..t.4f were wrong and so those variables got the unit s^2, which was the cause for the error you got2) You mixed up T.p and T.P (lower/upper case...
View ArticleRe: XY Plot
As I said before I am a beginner I asumed that I need units in order to plot. Yes the peak of the spikes should be at the beginnig of t.1a t.2a t.3a t.4a. This is what I`ve got.
View ArticleRe: XY Plot
In case you are missing the horizontal parts of the graph, you forgot about the last "else 0", so the graph was undefined outsides the spikes. I also changed the function name to i and changed the plot...
View Article.PTS file error
when ever i try to open pts file from my desktop to pro e it says no points found in pts file. while i have tried several times, kindly guide me where i'm doing wrong, the following are the points....
View ArticleRe: .PTS file error
You need 3 coordinates for each point. You'll select the meaning of the points by selecting the type of coordinate system. In this case, R, Theta, Z.
View ArticleRe: HOW TO CREATE MODEL OF WIRE ROPE
There is a lot of calculations going on with near or perfect tangency and this confuses the software. It is much better to assemble such an object than to make it a single part file.
View Article