Plot 2D slice view of any angle
Hi, I have a 3d plot on an rectangle range within x-y, I want to have a 2d slice view of the diagonal. Is there a way to achieve this ?
View ArticlePrevent part explosion
I want to explode everything except for one specific subassembly (or a particular selection of parts... whatever there is available) In the end, it should be possible to move these parts together when...
View ArticleUnable to make a gear
I've attached a picture:(consider opening on another tab to make it easier to see - middle button on many browsers) 1 - An axle/arbor (Pinned coincident to a datum axis - free on other directions)2 - A...
View ArticleRe: Plot 2D slice view of any angle
Shawn Fan wrote: Hi,I have a 3d plot on an rectangle range within x-y,I want to have a 2d slice view of the diagonal.Is there a way to achieve this ?There are several possibilities. Possibly the most...
View ArticleRe: "Modularization" of the program
I published post half an hour after you but it had been moderated for a few hours don't know why. Thanks for the attached worksheet. Nevertheless, I would like to ask you, if it is possible to use...
View ArticleClik here to view.
MC15 Box plot questions
Hello all, Am trying to present my data in a box plot: Is it possible to add a label to each of my boxes? Ideally under the X axis inline but anywhere on the graph would be fine. Looking at how it...
View ArticleRe: "Modularization" of the program
Yes it works, you help me a lot. I am much closer form finding "final solution", I think. Now I want to go for expressing function by Unit-A(X,Y,U)=Find(X,Y,U) - this should be more universal, I...
View ArticleClik here to view.
Re: The approximate straight of Chebysev (правило Чебышева)
If one link is shorter what is needed we can use not Find but MinError function. In this case this link will be.... rubber! "Та заспешила, всунула рыжую голову в форточку, вытянула сколько могла руку,...
View ArticleRe: I completely installed Creo but I do not know where to access it or open it?
Propably a bit late, but there is a copy of this thread somewhere else where I found a "solution": https://www.ptcusercommunity.com/message/301439#301439 Problem is the 64bit version. Don't know what...
View ArticleRe: "Modularization" of the program
It appears that you want to build a simulator like Hysys that solves blocks backwards and forwards instead of just forwards like most sequential modular flowsheet programs. Can it be done? I always...
View ArticleHow to extract non-consecutive submatrix in a easier way
Hi, everyone,If I have a 100 by 100 matrix and I want to extract its 10 to 20, 40 to 50 and 70 to 80 rows and columns,Is there a easier way rather than submatrix the rows first and then the columns and...
View ArticleClik here to view.
Re: How to extract non-consecutive submatrix in a easier way
Shawn Fan wrote: Hi, everyone,If I have a 100 by 100 matrix and I want to extract its 10 to 20, 40 to 50 and 70 to 80 rows and columns,Is there a easier way rather than submatrix the rows first and...
View ArticleRe: MC15 Box plot questions
As Richard says, to put text at various positions you really can't do much better than to look at the Amazing Images eBook. However, attached is an worksheet I knocked together for some reason or...
View ArticleRe: Prevent part explosion
You can unexploded the parts of the sub-asm and explode the sub-asm itself. Turn on the model tree explode status to quickly see the current state.
View ArticleRe: Prevent part explosion
ThanksGreat A good helper that button.Always there and I never saw it... But it's very confusing:Once I toggle the status, it goes back to the unexploded state, but does not go back to the original...
View ArticleClik here to view.
Sketch setup on Sweep
Why can't I change the sketch setup when drawing the sweep section ? The default view is upside down and all twisted...Can't draw this way ! There are no apparent options on the sweep setup that I can...
View Article2015 Submissions
I am the Project Manager for an RWDC team, located in Pleasanton, California. I am getting ready to submit our journal, however, I'm not sure who to send it to. Our state has no state coordinator, but...
View ArticleSurface plot
Hello, i am trying to plot this surface, but it is not showing. not sure what i am doing wrong. Thank you!
View ArticleRe: I want to access the PTC Windchill Flex PLM articles, I was able to do...
Hey Keith - now that our deployment is complete, can you confirm you're able to view the content within the FlexPLM community? Thanks.
View ArticleRe: Voting on product ideas turned off?
Dale - now that we've deployed our changes I wanted to confirm that you were once again able to participate in Product Ideas. Can you log out, then log back in and confirm?
View Article