Clik here to view.
Re: Mathcad to calculate magnetization
1. Denis Gorbunov wrote: ... It is correct in a sense that the low-field magnetization is (MEr-MCo) = 9 - 5 = 4 (magnetic moments are antiparallel), and the high field magnetization is (MEr + MCo) = 9...
View ArticleClik here to view.
Re: Mathcad to calculate magnetization
Doesn't this mean you are dealing with an anti-ferrimagnet (as opposed to a ferrimagnet)?!! No both, antiferromagnets and ferrimagnets, consist of at least two magnetic sublattices whose magnetic...
View ArticleClik here to view.
Re: Mathcad to calculate magnetization
Thanks for the animation! At B = 40 where the dM/dH slope changes the point jumps away and starts moving! Awesome! From your explanation it follows that a grid algorithm is really not complicated....
View ArticleRe: Mathcad to calculate magnetization
From your explanation it follows that a grid algorithm is really not complicated.No, it isn't. But the drawback, as usual for brute force, is that its slow as of the many calculations necessary. A grid...
View ArticlePTC Learning Connector Fails to Load
To whom it may concern, I was able to install and run Creo parametric 2.0 Student edition however when I try to open the PTC learning Connector nothing loads inside the box. I have tried reinstalling...
View ArticleSolver to iterate for target total volume?
Hello All, I am new to Creo coming from Catia. I have a sketch being extruded up to a complex surface (extrusion in the Z direction). My input is: total volume of the extrusion. My output should be...
View ArticleRe: Changing the background texture
Just in case this is what you are looking for, it was worthwhile making a document with regard to setting images as backgrounds for specific views. This is not an environment background, just a way to...
View Articlehow to get the variable's value in an external javascript
Hi,all. I defined a variable in the Arbortext Editor's command line,such as "$i=5",and I want to get the variable's value in an external javascript,what should I do?Thanks
View ArticleRe: Solver to iterate for target total volume?
There is no magic way to do this but there are ways if you can either do the calculation or if you are willing to go through a couple regenerations to get the answer back. If the volume is simple...
View ArticleRe: Mechanica..Elasto-plastic
For those following this thread I am finally getting around to summarizing what I found. I have discovered certain limitations using LDA, specifically the plasticity combined with contact, but I...
View ArticleRe: Assembly Cut Out Not Working
Oops, that is what I was afraid of. Creo full version cannot open university version files. Try contacting Timothy Brotherhood and see if he can help either convert the files for full version Creo or...
View ArticleRe: Creo Model
Jun, You do not have to restart the whole model if you just updated the wing. All the models are modular. If you only updated the wing, you can keep everything else the same. In the assembly file, make...
View ArticleClik here to view.
Re: Mathcad to calculate magnetization
Any specific question? I just looked at the routine AbsMin2(A) and it is really very tricky. It could easily be replaced bybut maybe match() was not available in MC2001. The routine determines the...
View ArticleClik here to view.
Re: Solid "Deep Drawing" (how to?)
I guess this answers the other question: why doesn't toroidal bend not work... Answer: it seems to do exactly what the double spinal bend does except a little simpler. But the distortion is still...
View ArticleRe: I'm getting tired of this! - helical sweep failures.
"So why does this work if you use a sweep along a guide creating exactly the same geometry?" Because it isn't creating exactly the same geometry. It is only very similar, but not the same. It probably...
View ArticleRe: I'm getting tired of this! - helical sweep failures.
It is certainly the same within the relative tolerance range. Every measure is identical to the Nth degree.
View ArticleRe: Proper Use of Centerlines?
There is no reason for the centerline to be extended to the edge of the part unless the centerline is depicting a rotational or a symmetry centerline. I see the few exceptions in the standards. There...
View ArticleClik here to view.
Re: I'm getting tired of this! - helical sweep failures.
You are limited to the filtered measurement reporting of the software, which is not the same as knowing the underlying models are identical. You can try generating a STEP file for each to see if the...
View ArticleRe: I'm getting tired of this! - helical sweep failures.
It only fails in the remove material mode, not the create solid or surface creation mode. And yes, they are identical in several export formats. Again, I need PTC to own up to this for the general...
View Article