Re: More lost data, more crashes. The hits just keep coming.......
I know this is just about a year old, we identified this same issue, little sad if you ask me that PTC makes Creo so dependant on windchill and makes Creo work so well with family tables but yet...
View ArticleRe: Mathcad provides incorrect solution
I don't know if this will negatively affect me anywhere else, but it fixes this problem.I doubt it. The option is there because sometimes an exact comparison is needed, but that's not ever likely to be...
View ArticleRe: Mathcad provides incorrect solution
I guess it was said before, but all I see is the effect of rounding and conversion as is to expect when dealing with computer floating point arithmetic. There is no simple way to avoid it and assuming...
View ArticleModel with simple frustrum - volume calculation wrong
I make a lot of models that involve pyramidal frustrums (transition of a rectangular section to another rectangular section, linearly). Rather than use the measured value calculated by Creo, I thought...
View ArticleCreo equivalent of SolidWorks configurations in parts?
Hi there, I've been with a new company using Creo 2.0 for the last three months and we would really benefit from being able to create parts with what I know as "configurations": I'm not sure what the...
View ArticleRe: Windchill 10.1 WGM Creo 2 compare status
Carl, we added the additonal status columns to our default workspace view and create some new table views without the status icons. By default I understand they are not displayed because it results...
View ArticleRe: Creo equivalent of SolidWorks configurations in parts?
Hi Andy, Family table in Creo Parametric is as Configuration in Solidworks and to use that functionality: 1. Create the part as sketch you attached.2. Select Tools > Family Table3....
View ArticleRe: Model with simple frustrum - volume calculation wrong
I think Creo is right. I'm not sure where the formula came from but ... L = l_base - ((l_base-l_top)/delta_z) * Z W = w_base - ((w_base-w_top)/delta_z) * Z A = L * W = l_base*w_base-...
View ArticleRe: Exclusion of a component
Are you looking for displacement in the Y direction for the entire assembly?
View ArticleRe: Model with simple frustrum - volume calculation wrong
I should be able to simplify the integral to be the same as the original formula, but so far no luck. I looked at the Wikipedia page that showed the derivation of the original formula, but it doesn't...
View ArticleRe: Model with simple frustrum - volume calculation wrong
I got the original formula from the CRC math tables. A handy book from olden times which has all sorts of nice answers to unusual geometry questions. It's an odd conundrum. One would, reasonably,...
View ArticleClik here to view.
Re: Helical Sweep, Ball and Worm Gear Assembly
This can be done at the lead-screw level and maintained with relations. As far as I can tell, this is correct and fully parametric.Funny thing is, I can change the 12.0 and nothing updates until I exit...
View ArticleRe: mechanism in fuel injector(mdx & mdo)
Regardless of what it happening in the specification, the mechanism is a simulation of some sort.If you have a "servo motor" that you are tracking the RPM, then you are asking for a trigger. I am not...
View ArticleHow to create clockwise rotation of shaft in pro e maecahnism
In my case I have assigned pin for the shaft & later defined force motor for the same. But If i run the analysis the shaft is rotating clock & anti clockwise .How to control, only it should run...
View ArticleRe: How to create clockwise rotation of shaft in pro e maecahnism
You probably have a motor profile defined that does this, such as a sine profile in conjunction with position. There are many ways to control a motor's motion. Typically I find that I have to use...
View ArticleRe: tracing the edge of a cutting tool (toolpath)
I have played around with that problem a little bit (still not implemented an outline algorithm) and thought I would post that intermediate result in case somebody else would like to give it a try...
View ArticleMultiple versions of the same part
HiCreo keeps in my memory, multiple versions of the same part.Example:123.PRT.1123.PRT.2123.PRT.3It is really annoying and takes up a lot of memory space. How can you disable it?
View ArticleRe: Multiple versions of the same part
This is normal procedure for saved parts. There will be occasions when you will be very thankful that this is the case. However, periodic maintenance will take care of this. There is a "purge.bat"...
View ArticleRe: Multiple versions of the same part
Thanks for the reply "Sometimes it required some help setting this up to function, but it has been part of Pro|E since the beginning." Can you explain more how I can check the settings? "You can also...
View ArticleRe: Helical Sweep, Ball and Worm Gear Assembly
Good idea, this would be sorta like a driving model or skeleton model of the assembly, cause it really seems like you can project to whole thing into 2D, and drive it from there. The sketch could be...
View Article